Polyaspartic · Perth & Peel
Epoxy Floor Perth installs polyaspartic floor coatings across Perth and the Peel region for garages, alfrescos, pool surrounds and shopfronts. Polyaspartic is UV-stable, so it will not yellow in the Perth sun, and most floors are done in one day with parking the next. It costs $70 to $120 per square metre installed, with a 5-year written warranty.
$70-$120 / m²
Installed polyaspartic
1 day
On site for most floors
24 hours
Until you park the car
UV-stable
Holds its colour in full sun
The problem
Most people look at polyaspartic for one of two reasons: a floor that has changed colour in the sun, or a floor they cannot do without for a week. If either sounds like you, read on.
Both problems come back to the same thing: standard epoxy was the wrong chemistry for the job.
Why it happens
Standard epoxy is a strong, affordable floor resin, but it was never designed for full sun or fast turnarounds. In Perth, four weaknesses show up again and again.
Most floor epoxies are aromatic resins, and sunlight breaks them down. In Perth’s strong UV the surface ambers within 12 to 24 months, and the change is most obvious on light colours and flake blends.
Epoxy needs 24 hours before you can walk on it and 5 to 7 days before you can park. For a family with one garage, or a business that cannot shut, that week is the real cost of the floor.
An epoxy topcoat left in full summer sun runs hotter and softer than one in a shaded garage. Outdoors it chalks, scuffs and loses gloss years before the base coat underneath wears out.
Rolling fresh epoxy over a yellowed floor only resets the clock, and coating over a glossy, unprepared surface can peel. The old surface needs grinding or sanding and a UV-stable topcoat.
The solution
Polyaspartic flooring is a coating made from aliphatic polyaspartic resin, a type of polyurea. Aliphatic resins do not break down in UV light, so the floor keeps its colour outdoors. It also cures in hours instead of days, which is why most polyaspartic floors take one day to install.
| Polyaspartic | Standard epoxy | Pure polyurea | |
|---|---|---|---|
| UV-stable | Yes | No | Depends on type |
| Walk on | 4-6 hours | 24 hours | Minutes |
| Park the car | 24 hours | 5-7 days | Hours |
| How it goes on | Rolled | Rolled | Sprayed by machine |
| Installed cost | $70-$120 / m² | $30-$90 / m² | Mostly industrial |
| Best for | Sun, speed, outdoors | Shaded indoor floors | Tanks, linings, industry |
Polyaspartic is a type of polyurea, slowed down enough to roll onto a floor. Pure polyurea sets so fast it has to be sprayed, so it suits industrial linings rather than homes. When people search for polyurea flooring in Perth for a garage or patio, polyaspartic is usually what they need.
Published prices
Polyaspartic flooring in Perth costs $70 to $120 per square metre installed, about $15 to $30 more per square metre than epoxy flake. A double garage in polyaspartic flake usually costs about $2,500 to $4,800. Your fixed price comes after a free on-site measure and slab test.
| Floor | Typical installed price |
|---|---|
| Double garage, 36-40 m² | About $2,500-$4,800 |
| Alfresco, patio or pool surround | $70-$120 / m² |
| UV topcoat over a sound epoxy floor | Quoted on measure |
| Driveway or carport | Quoted separately |
Every polyaspartic floor gets a fixed price after the measure. See the full guide to polyaspartic flooring cost in Perth.
Compare
On epoxy vs polyaspartic, polyaspartic is better when the floor gets direct sun or you cannot lose it for a week. Epoxy is better value for a shaded indoor floor where a week of curing does not matter. Use the table to match your floor.
| Your floor | Better choice | Why |
|---|---|---|
| Alfresco, patio or pool surround | Polyaspartic | Will not yellow in full sun |
| Garage facing north or west | Polyaspartic | Sun reaches the door line |
| Garage you need back tomorrow | Polyaspartic | Park after 24 hours |
| Shop, salon or clinic | Polyaspartic | Done overnight or in one day |
| Shaded garage, door mostly shut | Epoxy flake | Same strength, lower cost |
| Workshop or shed on a budget | Solid-colour epoxy | Lowest cost per m² |
Many of our garage floors combine both: an epoxy base for build and value, with a polyaspartic topcoat for UV and wear.
Where it is used
Polyaspartic suits any floor where sun, speed or both matter. These are the four jobs we do most.
Flake or solid-colour floors with parking the next day, and a door line that will not yellow.
UV-stable flake with an anti-slip finish, in lighter blends that stay cooler underfoot.
A heavier build for car tyres in full sun, quoted after we check the slab and drainage.
Installed overnight or in one day, so you open on time with a floor you can walk on.
See garage floor coating and commercial epoxy flooring.
One-day install
A one-day polyaspartic floor starts early and is walkable by evening. Polyaspartic sets fast, so the crew works in small sections with a short working time, which is why experience matters more than with epoxy.
01
We confirm the slab moisture reading, protect walls and doors, and degrease any stains.
02
The slab is diamond ground with vacuum extraction, and cracks are filled with a fast-setting resin.
03
The polyaspartic base goes down in sections. On flake floors, flake is broadcast to full cover.
04
Loose flake is scraped off, then a clear, UV-stable polyaspartic topcoat seals the floor.
05
Light foot traffic is fine after 4 to 6 hours. We walk the floor with you before we leave.
06
Vehicles can go back after 24 hours. Full chemical cure is reached at 7 days.
If the slab reads above 75% moisture, it needs a moisture-barrier primer that cures overnight, so the job runs over two days. We tell you at the measure, never on the day.
Yellowed floors
A yellowed epoxy floor can be recoated in polyaspartic if the coating underneath is still well bonded. We check it at the measure, sand or grind the surface to give the new coat a key, then apply a UV-stable polyaspartic topcoat. If the old floor is peeling or lifting, it is ground off first and treated as an epoxy floor repair.
Local service
We install polyaspartic flooring in every suburb from Yanchep to Mandurah and east to Kalamunda, at the same rates with a free measure. These are the jobs we see most in each part of Perth.
Alfrescos and pool surrounds in full sun, and yellowed outdoor coatings to recoat.
Mandurah 6210 · Rockingham 6168 · Scarborough 6019 · Hillarys 6025 · Cottesloe 6011
Showrooms and shopfronts done overnight or in a day, so trading is not interrupted.
Osborne Park 6017 · Malaga 6090 · Welshpool 6106 · Canning Vale 6155
Families with one garage who want the car back the next day. Every new slab is moisture tested.
Baldivis 6171 · Ellenbrook 6069 · Alkimos 6038 · Byford 6122
Exposed carports and verandahs that take afternoon sun.
Kalamunda 6076 · Forrestfield 6058 · High Wycombe 6057
Our work
Each project lists the suburb, the space, the finish and the time from start to parking.
Warranty
Every polyaspartic floor has a 5-year written workmanship warranty, plus the manufacturer’s warranty on the resin, handed to you in writing when we finish.
Why us
Polyaspartic is less forgiving than epoxy to install. These are the standards we hold every job to.
The reading decides one day or two.
No rushed, half-set edges.
No base coat showing.
Named under AS/NZS 4586.
A proper bond on every slab.
Backed by 7+ years in Perth.
Free measure
Tell us the space, the rough size and your suburb, or send photos of the floor you want to replace. We will confirm whether one day is realistic and give you a price range before the measure.
Polyaspartic flooring in Perth costs $70 to $120 per square metre installed. A double garage in polyaspartic flake usually costs about $2,500 to $4,800. That is about $15 to $30 more per square metre than epoxy flake, in return for UV stability and parking the next day.
Polyaspartic is better than epoxy for floors in direct sun and for jobs that cannot wait a week, because it is UV-stable and cures in hours. Epoxy is better value for shaded indoor floors. Both are strong and resist oil and hot tyres when installed properly.
Polyaspartic flooring does not yellow in sunlight, because it is made from aliphatic resin that UV light does not break down. That is why we use it on alfrescos, patios, pool surrounds and sunny garage door lines, where standard epoxy turns amber within 12 to 24 months.
You can drive on a polyaspartic floor after 24 hours and walk on it after 4 to 6 hours. Full chemical cure takes 7 days, so avoid spills, dragging heavy objects and hot tyres spinning on the floor during that first week.
Polyaspartic is a type of polyurea. Pure polyurea sets in seconds and must be sprayed by machine, so it is used for industrial linings. Polyaspartic is modified to set more slowly, so it can be rolled onto floors, and it is UV-stable.
Polyaspartic can go over existing epoxy if the epoxy is still well bonded. We sand or grind the surface so the new coat can key in, then apply the UV-stable topcoat. A peeling or lifting epoxy floor must be ground off first.
Polyaspartic is the right chemistry for a Perth driveway, because it handles sun and car tyres. Driveways need a heavier build than a patio and good drainage, so we check the slab, cracks and falls on site and quote driveways separately.
We install polyaspartic flooring anywhere in the Perth metropolitan area and the Peel region, including Mandurah, Rockingham, Osborne Park, Malaga, Baldivis and Kalamunda. Every suburb gets the same rates and a free measure. Call 0432 666 474 with your suburb and the space you want coated.
We are a Perth epoxy flooring contractor. We coat garages, warehouses, commercial kitchens and showrooms across the Perth metropolitan area and the Peel region
Copyright © 2026 All Right Reserved Epoxy Floor Perth