FAQs
Straight answers to the 35 questions Perth customers ask most about epoxy flooring: what it costs, which system to choose, how long it takes to cure, how it handles the Perth sun, and what the 5-year warranty covers.
5 questions
Prices are typical installed ranges for Perth floors. Your fixed price comes after a free on-site measure.
Epoxy flooring cost in Perth
Epoxy flooring in Perth costs $30 to $150 per square metre installed. Solid-colour epoxy sits at the low end and metallic epoxy at the top. A double garage in flake usually costs $2,100 to $3,400. Slab condition, cracks and moisture treatment move the final price, which we fix in writing after a free on-site measure.
A double garage of 36 to 40 m² in epoxy flake usually costs $2,100 to $3,400 installed in Perth. A single garage is usually $1,200 to $1,900 and a triple $3,000 to $4,800. Oil stains, cracks and slab moisture can add to the price, which we fix in writing after a free measure.
Polished concrete is not always cheaper than epoxy. A simple grind and seal starts lower than most epoxy systems, at around $50 per square metre. Full mechanical polishing on a poor-quality slab can cost more than a flake floor. The slab's condition usually decides which is better value.
The quote is free. We measure your floor on site, test the slab moisture and send a written fixed-price quote, with no obligation to go ahead. There is no call-out fee anywhere in the Perth metropolitan area or the Peel region.
We can give you a price range over the phone. Most Perth floors cost $30 to $150 per square metre installed, and a double garage in flake usually costs $2,100 to $3,400. The fixed price comes after the free on-site measure, because slab condition changes the cost.
5 questions
Choose the system for how the floor is used, not how it looks.
Epoxy is a two-part resin that bonds to ground concrete and cures 0.3 to 6 mm thick. Floor paint is a thin film that sits on the surface. Paint often lifts under hot tyres within 2 to 3 years, while a correctly installed epoxy floor lasts 10 to 20 years.
Flake flooring is an epoxy floor with coloured vinyl flakes spread into the wet base coat, then sealed under a clear topcoat. It is the most popular garage finish in Perth because it hides dust and tyre marks and adds grip. It costs $55 to $90 per square metre installed.
Polyaspartic is better than standard epoxy for floors in the sun and for jobs that cannot wait a week. It is UV-stable, so it does not yellow, and you can drive on it after 24 hours. It costs more than epoxy, at $70 to $120 per square metre installed.
Metallic epoxy is a decorative floor with metallic pigments that create a marble or swirl effect. It suits showrooms, shops and indoor living areas, and costs $80 to $150 per square metre installed. It has the lowest slip rating of our systems, so we do not use it outdoors or in wet areas.
Choose polished concrete if the slab is sound and you want the concrete itself as the finish, with no coating to recoat later. Choose epoxy if the slab is stained, cracked or dusting, or you want colour, flake or a non-slip texture. We check the slab at the measure and recommend one.
5 questions
What to expect on the day, and how long until you can use the floor.
A double garage takes one to two days on site. Larger homes and commercial floors take two to five days, depending on the system and the floor size. Commercial and industrial floors can be done in stages and outside trading hours, so you keep operating.
You can drive on a new epoxy garage floor after 5 to 7 days, and walk on it after 24 hours. A polyaspartic floor cuts that to 24 hours for cars and 4 to 6 hours for foot traffic. Avoid hot tyres, spills and dragging heavy objects until the full 7-day cure.
We can work in occupied homes and trading businesses. Vacuum-extracted grinding captures about 90% of airborne dust, so the rest of the house or premises stays usable. Commercial floors are done in stages and outside trading hours where needed, so you can keep operating.
Clear the floor completely and park vehicles off the slab for the cure period. We handle everything else, including grinding off old coatings and paint, repairing cracks and cleaning up after the job. Tell us about any floor drains or expansion joints you know of.
Epoxy cannot go over paint. The paint must be ground off completely, or the new floor lifts with it. Sound, fully bonded tiles can be coated once the glaze is ground off and the grout lines are filled. Loose or drummy tiles must be removed first. Grinding off old coatings is included in our preparation.
4 questions
Two Perth conditions decide how long a floor lasts: strong UV and new slabs coated too early.
Polyaspartic flooring
Standard epoxy yellows in direct Perth sun, often within 12 to 24 months. A UV-stable aliphatic polyaspartic or polyurethane topcoat stops it. We specify a UV-stable topcoat on every floor that gets sun, including alfrescos, patios, carports and the area just inside a north- or west-facing garage door.
Epoxy works outdoors in Perth only with a UV-stable topcoat, such as aliphatic polyaspartic. Standard epoxy yellows in direct sun within 12 to 24 months. Outdoor floors such as alfrescos, patios, pool surrounds and driveways also need a textured finish for grip when wet.
A new slab needs at least 28 days before it can be coated. Age alone is not enough, so we test the slab's relative humidity first. Any reading above 75% needs a moisture-barrier primer. This matters most in new estates such as Baldivis and Ellenbrook, where slabs are often coated too early.
A slab moisture test measures the relative humidity inside the concrete before it is coated. Moisture rising through the slab is a main cause of epoxy peeling. We test every slab and write the reading on your job sheet. Any reading above 75% gets a moisture-barrier primer first.
4 questions
How long a floor lasts, and how to keep it looking new.
A correctly installed epoxy floor lasts 10 to 20 years in Perth. Flake and polyaspartic systems reach the top of that range. How long a floor lasts depends far more on slab preparation than on the resin brand, which is why we grind every slab and test its moisture before coating.
Clean an epoxy floor by sweeping or vacuuming, then mopping with warm water and a pH-neutral cleaner. Avoid acidic cleaners, citrus degreasers and scouring pads, which dull the topcoat. Wipe up oil and fuel spills promptly. A well-kept floor keeps its gloss for years without recoating.
Smooth, glossy epoxy is slippery when wet. Flake texture, anti-slip additives and textured topcoats raise the slip rating. We rate floors to AS/NZS 4586, the Australian slip-resistance standard, and name the rating on your quote to suit how the floor is used, from a home garage to a commercial kitchen.
Epoxy resists scratching from normal foot and vehicle traffic, but dragging heavy or sharp objects can scratch the topcoat. Flake floors hide light scratches well. Use felt pads under furniture and lift heavy equipment rather than drag it. A worn topcoat can be recoated without replacing the floor.
4 questions
Systems are chosen for the loads, chemicals and cleaning on your site.
Commercial epoxy flooring
We install commercial and industrial floors across Perth, including warehouses, factories, workshops, cool rooms, commercial kitchens, shops, gyms and medical centres. Each system is chosen for the real loads, chemicals and cleaning on your site, from forklift traffic to hot washdowns.
We install food-grade, HACCP-compliant floors for commercial kitchens and food production areas. They are seamless, non-porous, coved where they meet the walls and suited to your cleaning chemicals and hot washdowns, so they pass hygiene audits that porous or jointed floors fail.
The slip rating your floor needs depends on how it is used. Wet areas, ramps and commercial kitchens need a higher rating than a dry showroom. We install to AS/NZS 4586, the Australian slip-resistance standard, name the rating on your quote and supply product test data on request.
We can work outside trading hours where your site needs it. Large floors are done in stages, so part of the site stays in use while we work on the rest. We agree the schedule with you before the job starts, so there are no surprises for your staff or customers.
4 questions
Most failed floors can be fixed without replacing the slab, once the cause is found.
Epoxy floor repair in Perth
Most peeling epoxy floors can be repaired without replacing the slab. We find the cause first, usually an unground, sealed or damp slab, then grind back the failed coating and reinstall on a properly prepared surface. Recoating over the same fault means the floor fails again.
An epoxy floor bubbles when air escapes from the concrete while the coating cures, leaving pinholes. It is more common on porous or warm slabs. The fix is to grind back the affected area, apply a primer that seals the slab, and recoat.
Hot tyre pickup happens when a coating too soft for cars softens under warm tyres and lifts off with them. It is common with floor paint and thin DIY kits. The fix is grinding back to bare concrete and installing a hot-tyre-rated epoxy or polyaspartic system.
A yellowed epoxy floor can be fixed with a UV-stable recoat. We clean and lightly grind the existing floor, then apply an aliphatic polyaspartic topcoat that holds its colour in the sun. If the floor underneath is sound, the whole system does not need replacing.
4 questions
Where we work, and what the 5-year warranty covers.
We install epoxy flooring anywhere in the Perth metropolitan area and the Peel region, from Yanchep to Mandurah and east to Kalamunda. That includes Joondalup, Rockingham, Midland, Canning Vale, Baldivis and Ellenbrook. The on-site measure and quote are free across that whole area. Regional WA jobs are quoted case by case.
We do not charge more for jobs outside central Perth. Every suburb in the Perth metropolitan area and the Peel region gets the same rates, a free on-site measure and no call-out fee. Your price depends on the floor size, the system and the slab condition, not your postcode.
Every installation has a 5-year written workmanship warranty covering bond failure, delamination and premature wear under normal use, plus the manufacturer's warranty on the resin. It does not cover impact damage, chemicals beyond the specified system, structural slab movement or damage from the wrong cleaning products.
We quote regional Western Australia case by case. Call 0432 666 474 with the town and the floor area, and we will tell you straight away whether we can take the job on and what the travel adds. Inside Perth and Peel, there is no travel charge.
Still unsure?
Every floor is different. Call or send a few photos and we will answer your question, then book a free on-site measure if you want a fixed price.
We are a Perth epoxy flooring contractor. We coat garages, warehouses, commercial kitchens and showrooms across the Perth metropolitan area and the Peel region
Copyright © 2026 All Right Reserved Epoxy Floor Perth