Flake floors · Perth & Peel

Flake Flooring Perth

Epoxy Floor Perth installs epoxy flake flooring across Perth and the Peel region for garages, alfrescos, patios, pool surrounds and laundries. Every flake floor is fully broadcast, so no base coat shows through, and every outdoor floor gets a UV-stable topcoat. Flake flooring costs $55 to $90 per square metre installed, with a 5-year written warranty.

$55-$90 / m²

Installed epoxy flake

P4-P5

Typical slip rating, AS/NZS 4586

15-20 years

Typical life of a flake floor

5 years

Written workmanship warranty

The problem

Does your alfresco, garage or laundry floor look worn out?

Bare concrete and painted floors wear out in the same few ways around a Perth home. If any of these sound familiar, a flake floor is usually the fix.

A plain coating would seal the surface but show every mark. Flake hides them.

Why it goes wrong

What goes wrong with cheap flake floors in Perth?

Most flake floors that fail in Perth were cheap for the same four reasons: the wrong topcoat, too little flake, no slip rating and a slab that was never ground. Each one shows up within a couple of summers.

Standard topcoats yellow outside

A clear epoxy topcoat turns amber under Perth sun, and on a light flake blend the change is obvious within 12 to 24 months. Alfrescos, patios and pool surrounds need an aliphatic polyaspartic or polyurethane topcoat that holds its colour.

Partial flake shows the base coat

Some installers scatter flake lightly to save material. The base coat shows between the chips, the floor looks patchy, and the thin topcoat wears through sooner. A full broadcast covers the base completely before it is sealed.

No slip rating near water

A smooth gloss topcoat over flake can still be slippery when wet. Around pools, outdoor showers and laundry tubs, the topcoat needs texture or an anti-slip additive, chosen for a slip rating under AS/NZS 4586.

Coating over an unground slab

Flake laid over washed or acid-etched concrete has little to grip. It starts lifting at the edges and around drains, often after the first hot summer. Diamond grinding is the step cheap quotes leave out.

The solution

What is flake flooring?

Flake flooring is an epoxy floor with coloured vinyl flakes broadcast into the wet base coat and sealed under a clear topcoat. The flakes add colour, texture and grip, and hide dust, stains and small marks. It is the most popular decorative floor coating for Perth homes.

Full broadcast (our standard)Partial broadcast
Flake coverageBase coat fully coveredBase coat shows between flakes
Texture and gripEven across the floorSmooth patches between flakes
Hides dust and marksVery wellPartly
Topcoat wearSpread evenlyFaster over the gaps
LookGranite or terrazzo effectSpeckles on a plain base

Flake flooring is still an epoxy floor. The difference between flake flooring and plain epoxy is the finish on top, not the resin underneath, so slab preparation matters just as much.

Published prices

How much does flake flooring cost in Perth?

Flake flooring in Perth costs $55 to $90 per square metre installed. A 36 to 40 m² double garage usually costs $2,100 to $3,400, and polyaspartic flake for sunny outdoor areas costs $70 to $120 per square metre. Your fixed price comes after a free on-site measure.

Typical flake flooring prices

SpaceTypical sizeTypical installed price
Laundry or bathroomUnder 15 m²Minimum charge, quoted on measure
Single garage18-21 m²$1,200-$1,900
Double garage36-40 m²$2,100-$3,400
Alfresco, patio or pool surroundAny size$70-$120 / m² (polyaspartic flake)

What moves a flake floor price

Every flake floor coating we quote in Perth gets a fixed price after the measure. See the full guide to flake flooring cost in Perth.

Colours and blends

Which flake colour and blend should you choose?

Choose a flake blend close to the colour of your walls, pavers or cabinetry, and go lighter for outdoor floors in full sun. Mid-grey and earthy blends hide dust and dirt best, so they suit garages and busy patios.

Blends that suit each space

SpaceBlend that worksWhy
GarageMid to dark grey, charcoalHides tyre marks and dust
Alfresco and patioLight grey, sandstone, earth tonesStays cooler underfoot in the sun
Pool surroundLight, cool blendsCooler on bare feet, pairs with coping
Laundry and bathroomSoft greys, whites, beigesBrighter room, easy to keep clean
Workshop or shedDarker blendsHides oil and scuffs

How to choose with confidence

We bring physical flake samples to the measure, so you see each blend on your own slab and in your own light. Small chips give a fine granite look and larger chips a bolder terrazzo effect, across hundreds of blends. Browse our epoxy flooring colours before we arrive.

Alfrescos, patios, pools

Can flake flooring go outdoors?

Flake is one of the best alfresco flooring options in Perth when it has a UV-stable topcoat and a textured finish. We use an aliphatic polyaspartic topcoat on every alfresco, patio, pool surround and balcony, so the floor holds its colour and keeps its grip when wet.

Indoor flake (garage, laundry)Outdoor flake (alfresco, patio, pool)
TopcoatEpoxy or polyasparticAliphatic polyaspartic
FinishStandard textureTextured or anti-slip
Walk on24 hours4-6 hours
Installed cost$55-$90 / m²$70-$120 / m²

Driveways carry car tyres in full sun, so they need a heavier system than a patio and are quoted separately. See polyaspartic flooring.

Our process

How do we install a flake floor?

Every flake floor goes through six stages over one to two days. The two that decide how it looks are the full broadcast and the scrape-back, which turn loose chips into a flat, even surface.

01

Test and plan

We measure the area, test the slab moisture and confirm your blend and topcoat.

02

Grind and repair

The slab is diamond ground with vacuum extraction, cracks are filled and joints are kept.

03

Prime and base coat

A primer seals the slab, then a base coat tinted to match your flake blend goes down.

04

Broadcast to full cover

Flake is thrown by hand into the wet base until no base coat shows anywhere.

05

Scrape and vacuum

Loose and standing chips are scraped flat and vacuumed off for an even surface.

06

Seal

One or two clear topcoats seal the flake, UV-stable outdoors and anti-slip near water.

Downtime

When can you use your new flake floor?

You can walk on an epoxy flake floor after 24 hours and drive on a flake garage floor after 5 to 7 days. Outdoor flake with a polyaspartic topcoat takes foot traffic after 4 to 6 hours. Full chemical cure takes 7 days.

Keep barbecues, pot plants and metal-legged furniture off the floor until the cure is complete, then use felt pads and plant saucers to protect the topcoat.

Local service

Do you install flake flooring near me?

We install flake flooring in every suburb from Yanchep to Mandurah and east to Kalamunda, at the same rates with a free measure. The most common flake job changes across Perth.

Coastal alfrescos and patios

Full-sun outdoor floors, so polyaspartic topcoats and lighter blends that stay cooler underfoot.

Mandurah 6210 · Rockingham 6168 · Scarborough 6019 · Hillarys 6025 · Fremantle 6160 · Cottesloe 6011

New-estate garages

Fresh slabs, so every one is moisture tested before the base coat goes down.

Baldivis 6171 · Ellenbrook 6069 · Alkimos 6038 · Byford 6122 · Banksia Grove 6031

Established homes

Laundries and patios with old tiles or paint that must be ground off first.

Joondalup 6027 · Willetton 6155 · Applecross 6153 · Morley 6062 · Midland 6056

Hills properties

Large sheds and verandahs that suit a tough, darker blend.

Kalamunda 6076 · Forrestfield 6058 · High Wycombe 6057

Our work

Recent flake floors across Perth

Each project lists the suburb, the space, the blend and the floor size, so you can picture it on your own floor.

Warranty

What does the warranty cover on a flake floor?

Every flake floor has a 5-year written workmanship warranty, plus the manufacturer’s warranty on the resin, handed to you in writing when we finish.

What is covered

What is not covered

Why us

Why choose Epoxy Floor Perth for flake flooring?

Six standards every flake floor we install meets, which you can check against any other quote.

Full broadcast as standard

No base coat showing.

UV-stable outdoors

Polyaspartic on every sunny floor.

Slip rating on the quote

Named under AS/NZS 4586.

Samples on your slab

See the blend in your own light.

Ground, never etched

A proper bond on every slab.

5-year written warranty

Backed by 7+ years in Perth.

Free measure and samples

Get a fixed price for your flake floor

Tell us the space, the rough size and your suburb, or send a few photos. We will give you a price range and bring flake samples to a free on-site measure.

Name

FAQ

Flake flooring questions

More answers on our epoxy flooring FAQs page.

Flake flooring in Perth costs $55 to $90 per square metre installed with an epoxy topcoat, and $70 to $120 with a UV-stable polyaspartic topcoat for outdoor areas. Small floors under 15 m² carry a minimum charge. Your fixed price comes after a free on-site measure and slab test.

Flake flooring is not slippery in normal use, because the chips give the surface texture. It typically rates P4 to P5 under AS/NZS 4586. Near pools, showers and taps we add an anti-slip additive to the topcoat and name the slip rating on your quote.

Flake flooring can go around a pool when it has a UV-stable polyaspartic topcoat and an anti-slip finish. Lighter blends stay cooler on bare feet in full sun. We check the slab and the drainage at the measure, and quote the slip rating before work starts.

Flake flooring with a standard epoxy topcoat yellows in direct Perth sun within 12 to 24 months. With an aliphatic polyaspartic topcoat it holds its colour. We use a UV-stable topcoat on every outdoor flake floor and on garage door lines that get sun.

Flake flooring can go over sound, fully bonded tiles once the glaze is ground off and the grout lines are filled level. Loose or drummy tiles must be removed first. We tap-test every tiled floor at the measure and tell you which option your floor needs.

A flake floor lasts 15 to 20 years when the slab is ground, moisture tested and fully broadcast. Outdoor floors last longest with a UV-stable topcoat. A worn topcoat can be recoated after many years without replacing the flake layer underneath.

Flake flooring is a type of epoxy flooring. Both use the same resin base coat over a ground slab. Flake flooring adds coloured vinyl chips and a clear topcoat, which hide dust and marks and add grip. Plain epoxy has a smooth, solid-colour finish instead.

We install flake flooring anywhere in the Perth metropolitan area and the Peel region, including Mandurah, Rockingham, Baldivis, Joondalup, Ellenbrook and Kalamunda. Every suburb gets the same rates and a free on-site measure. Call 0432 666 474 with your suburb and the space you want coated.