Floor repair · Perth & Peel

Epoxy Floor Repair Perth

Epoxy Floor Perth repairs peeling, bubbling, lifting and yellowed epoxy floors across Perth and the Peel region, including floors another installer laid. We find out why the floor failed before we touch it, fix that cause, then recoat. Every repair we do carries a 5-year written workmanship warranty.

Diagnosis first

Moisture, adhesion and slab checks

Any installer

We repair floors others laid

Photos welcome

Free assessment before the measure

5 years

Written warranty on our repair

The problem

Is your epoxy floor peeling, bubbling or lifting?

Epoxy floors rarely fail all at once. They start with a small sign that is easy to ignore, then spread. These are the signs Perth homeowners and businesses send us photos of most.

Each of these has a cause in the slab or the original install, and the cause decides the fix.

Why it fails again

Why do patch-ups and quick recoats fail again?

Most failed floors we see have already been patched or recoated once. The same fault was still underneath, so the new coat failed the same way, usually faster. These are the four mistakes behind a second failure.

Recoating over the fault

A fresh coat rolled over a floor that is lifting only bonds to the coating beneath it. When the old layer lets go, the new one goes with it, often within a few months.

Ignoring slab moisture

If moisture pushed the first coating off, it will push the second one off too. Without a moisture reading and a moisture-barrier primer, a recoat on a damp slab is the same failure on a timer.

Patching with a different product

DIY patch kits and mismatched resins cure at different rates and look different. The edges of the patch become the next weak point, and the colour never quite blends in.

Leaving the edges loose

Coating that has started to lift keeps lifting from its edges. A repair that does not cut back to firmly bonded coating leaves a loose edge for water and dirt to work under.

Diagnosis

What causes an epoxy floor to fail?

Nearly every epoxy floor failure comes from one of six causes, and each shows a different sign. Matching the sign to the cause is the first thing we do on site, because it decides whether the fix is a spot repair or a full recoat.

What you seeMost likely causeHow we fix it
Peeling or delaminationSlab not ground, sealed, or damp when coatedGrind back to sound concrete, prime, reinstall
Bubbles or pinholesAir escaping from the slab as the coating curedGrind out, seal-coat the slab, recoat
Hot tyre pickupCoating too thin or soft for carsRemove, reinstall a hot-tyre-rated system
YellowingTopcoat not UV-stableSand and recoat in UV-stable polyaspartic
Cracks through the coatingSlab movement or an unfilled crackConcrete crack repair, then recoat
Worn lanes or dull patchesTopcoat worn through by trafficSand and apply a fresh topcoat

Hot tyre pickup and yellowing are the two most common failures on Perth garage floors, because of summer heat and strong sun at the door line. Most garage floor repair in Perth starts with one of those two.

Your options

Should your floor be repaired or replaced?

Your floor can be repaired if most of the coating is still firmly bonded and the cause is fixable. It needs replacing if the coating is lifting across large areas or the slab problem affects the whole floor.

Spot repair

Used when a small area has failed and the rest of the floor is sound. We cut back to firmly bonded coating, grind the exposed concrete, fix the cause and rebuild the area to match. On flake floors we blend the flake so the repair is hard to see.

Topcoat renewal

Used when the floor is bonded but the surface is yellowed, dull or worn. We clean and sand the whole floor, then apply a new topcoat. Choosing UV-stable polyaspartic at this point stops yellowing coming back.

Full removal and reinstall

Used when the coating is lifting widely, was laid over paint, or sits on a damp slab. We grind the whole floor back to bare concrete, treat the slab and install a new system with a moisture-barrier primer where needed.

Pricing

How much does epoxy floor repair cost in Perth?

Epoxy floor repair in Perth is priced after an inspection, because the cost depends on how much has failed and why. A full removal and reinstall costs the normal installed price of the new system, $30 to $150 per square metre, plus the cost of grinding off the failed coating.

Repair typeHow it is priced
Spot repairQuoted after inspection, by area and cause
Topcoat renewal over a sound floorQuoted per m² after a bond check
Full removal and reinstallSystem price ($30-$150 / m²) plus removal
Moisture-barrier primerAdded only when the slab reads above 75%

Send photos first and we can usually tell you which repair type you need and a likely price range before we visit. See epoxy flooring cost in Perth.

Our process

How do we repair a failed epoxy floor?

Every repair follows the same six steps, and the first three happen before any coating is touched.

01

Review your photos

Wide shots and close-ups tell us the likely cause and which repair type to plan for.

02

Inspect on site

We tap-test the coating to map loose areas and check adhesion at the edges.

03

Test the slab

A moisture reading shows whether damp caused the failure and whether a barrier primer is needed.

04

Remove the failure

Failed coating is ground back to firmly bonded edges, or the whole floor to bare concrete.

05

Fix the cause

Cracks are routed and filled, damp slabs are primed with a moisture barrier, and soft systems are replaced.

06

Recoat and hand over

The new system goes down, matched or upgraded, and you get the moisture reading and written warranty.

Any floor

Can you repair a floor another company installed?

We repair floors laid by other installers and by owners with DIY kits. We do not need the original product details, because the inspection and moisture test tell us what we need. Our 5-year written warranty covers the work we do, and on a full reinstall it covers the whole new floor.

Local service

Do you repair epoxy floors near me?

We repair epoxy floors in every suburb from Yanchep to Mandurah and east to Kalamunda, at the same rates with free photo assessments. The failures we see change across Perth.

New estates

Peeling within the first year, usually from slabs coated before they were dry.

Baldivis 6171 · Ellenbrook 6069 · Alkimos 6038 · Byford 6122 · Banksia Grove 6031

Sunny coastal homes

Yellowed and chalky outdoor coatings that need a UV-stable recoat.

Mandurah 6210 · Rockingham 6168 · Scarborough 6019 · Hillarys 6025 · Fremantle 6160

Established suburbs

Garage paint and DIY kits lifting under hot tyres, ground off and replaced.

Joondalup 6027 · Morley 6062 · Willetton 6155 · Midland 6056 · Gosnells 6110

Industrial estates

Worn forklift lanes and chemical damage, repaired in stages so the site keeps running.

Welshpool 6106 · Malaga 6090 · Wangara 6065 · Canning Vale 6155

Warranty

What does the repair warranty cover?

Every repair carries a 5-year written workmanship warranty on the work we do, plus the manufacturer’s warranty on the new resin. On a full reinstall, the warranty covers the whole floor.

What is covered

What is not covered

Why us

Why choose Epoxy Floor Perth for epoxy floor repair?

Repair work is diagnosis first and coating second. These are the standards every repair meets.

Cause found first

Before any grinding starts.

Moisture tested

Reading recorded in writing.

Cut back to sound edges

No loose coating left behind.

Matched or upgraded

Flake blended, topcoats UV-stable.

Any installer's floor

No original paperwork needed.

5-year written warranty

Backed by 7+ years in Perth.

Free photo assessment

Send photos of your failed floor

Email or WhatsApp a wide shot of the floor and close-ups of the damage, with your suburb. We will tell you the likely cause and repair type, then book a free on-site inspection.

Name

FAQ

Epoxy floor repair questions

More answers on our epoxy flooring FAQs page.

Epoxy floor repair in Perth is priced after an inspection, because it depends on how much has failed and why. Small spot repairs cost far less than a new floor. A full removal and reinstall costs the system price of $30 to $150 per square metre, plus removal of the old coating.

A new epoxy floor usually peels because the slab was not diamond ground, was sealed, or was still damp when it was coated. New-estate slabs coated in the first months are the most common case. A moisture test on site confirms the cause before any repair.

We can fix just the damaged section when the rest of the floor is still firmly bonded. We cut back to sound coating, fix the cause and rebuild the area to match. If tap-testing shows loose coating across the floor, a spot repair would fail, so we recommend a full recoat.

We can repair a lifting DIY epoxy kit, but it almost always means grinding the whole kit off. DIY kits are usually thin and laid over acid-etched concrete, so the parts still stuck are close to failing too. The new floor is installed on a properly ground slab.

Hot tyre pickup is fixed by removing the soft coating and reinstalling a system rated for hot tyres. Patching the tyre tracks does not work, because the same coating will lift again next summer. The new floor is ground, built to the right thickness and sealed with a hot-tyre-rated topcoat.

A yellowed epoxy floor cannot be bleached back, but it can be recoated. If the floor is well bonded, we sand it and apply a UV-stable polyaspartic topcoat that will not yellow. The floor keeps its colour from then on, even in full sun.

Most epoxy floor repairs take one to two days on site. A spot repair or topcoat renewal is often done in a day. A full removal and reinstall of a double garage takes about two days, plus the normal cure time before you park on it.

We repair epoxy floors anywhere in the Perth metropolitan area and the Peel region, including Baldivis, Ellenbrook, Rockingham, Joondalup, Mandurah and Welshpool. Every suburb gets the same rates and a free photo assessment. Call or WhatsApp 0432 666 474 with photos and your suburb.